Quantum SDLT 320 Podręcznik Użytkownika Strona 45
- Strona / 102
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
SDLT 220 and SDLT 320 Design & Integration Guide CHAPTER 2: General Drive Specifications
81-81148-01 March 2004 2-27
2.9.3 Front Panel Cleaning Light
The Cleaning Required (yellow) LED on the front panel indicates to the operator
that cleaning is needed. This feature is enabled by the EEPROM parameter
EnaCleanLight. The location of the Cleaning Required LED (and other front
panel LEDs) is shown in Figure 2-7.
Figure 2-7. Front Panel LEDs
If EnaCleanLight is enabled, the yellow LED illuminates steadily for these
conditions:
• When a HWE(Hard Write Error)/HRE(Hard Read Error) is encountered, and
more than 100 hours have passed since the last cleaning.
Once illuminated, the yellow LED stays lit until one of the following occurs:
1) drive is cleaned successfully, or 2) the drive is reset due to a firmware failure or
firmware update, or 3) power is cycled off and on.
1 Amber LED
SDLT 220: Write Protect
SDLT 320: Drive Density
2 Green LED
Drive Status
3 Yellow LED
Cleaning Required
4 Eject Button
- Copyright 2
- Trademarks 2
- Legal Disclaimers 2
- Contact Information 2
- Revision History 3
- Table of Contents 5
- 81-81148-01 March 2004 vii 7
- List of Tables 9
- List of Figures 11
- Introduction 13
- 1.2 Referenced Documents 14
- 1.3 Related Documents 14
- 1.4 Structure of this Manual 15
- 1.5 Conventions 16
- 1.6 For More Information 17
- 1.7 Reader Comments 17
- 1.8 Quantum Diagnostics Tools 18
- General Drive 19
- Specifications 19
- 2.2 SDLT Product Features 20
- 1 Amber LED 21
- 2 Green LED 21
- 3 Yellow LED 21
- 4 Eject Button 21
- 2.3 Dimensions and Tolerances 22
- 81-81148-01 March 2004 2-5 23
- 2-6 March 2004 81-81148-01 24
- 2.4 Physical Dimensions 25
- Orientation Looks Like This 26
- Typical (Top Side Up) 26
- Left Side Down 26
- Right Side Down 26
- 2.5 Reliability 27
- 2.5.4 Data Integrity 28
- Mechanism 29
- 2.6 Functional Specifications 30
- 81-81148-01 March 2004 2-13 31
- 2-14 March 2004 81-81148-01 32
- 2.6.5 Storage Capacity 33
- 2-16 March 2004 81-81148-01 34
- 81-81148-01 March 2004 2-17 35
- 2.7.2 Air Flow Requirements 36
- 2.7.3 Storage and Shipment 37
- 2.7.4 Altitude 37
- 2-20 March 2004 81-81148-01 38
- ≤ 20 lbs 39
- ≤ 50 lbs 39
- 2-22 March 2004 81-81148-01 40
- 81-81148-01 March 2004 2-23 41
- 2-24 March 2004 81-81148-01 42
- • Cleaning Requested 43
- • Cleaning Required 43
- • Cleaning Tape Expired 43
- SCSI Cleaning Error Reporting 44
- Figure 2-7. Front Panel LEDs 45
- 2-28 March 2004 81-81148-01 46
- Electrical Specifications 47
- 3-2 March 2004 81-81148-01 48
- 3.2 Power Supply Tolerances 49
- 3-4 March 2004 81-81148-01 50
- Thermal Specifications 51
- 4.2 Air Flow Measurements 52
- 81-81148-01 March 2004 4-3 53
- 4-4 March 2004 81-81148-01 54
- 81-81148-01 March 2004 4-5 55
- 4-6 March 2004 81-81148-01 56
- 81-81148-01 March 2004 4-7 57
- SDLT 320 58
- Embedded Bezel 59
- Library Bezel 60
- Regulatory Requirements 61
- 5.1.2 Safety Requirements 62
- 81-81148-01 March 2004 5-3 63
- 5.2.3 Conducted Emissions 64
- 5.2.4 Radiated Emissions 64
- Quantum tape drive products 65
- 5.3 Acoustic Noise Emissions 66
- SCSI and Controller 67
- Interface Specification 67
- 6.2 Setting the SCSI ID 68
- 81-81148-01 March 2004 6-3 69
- 6-4 March 2004 81-81148-01 70
- 6.3 Hardware (Connectors) 71
- 6.4 SCSI Stub Lengths 72
- 6.5 SCSI Cable Length 72
- 6.6 Power On Self Test 73
- 6.7 SCSI Command Timeout 73
- 6-8 March 2004 81-81148-01 74
- 6.8 SCSI and Power Connectors 75
- • Connector body: 51110-0850 76
- Figure 6-4. Loader Connector 76
- (Internal Version Shown) 76
- 81-81148-01 March 2004 6-11 77
- 6-12 March 2004 81-81148-01 78
- 81-81148-01 March 2004 6-13 79
- 6-14 March 2004 81-81148-01 80
- 81-81148-01 March 2004 6-15 81
- 6.10 Configuring the Drive 82
- Updating the Firmware 83
- 7.1.2 Making a FUP/CUP Tape 84
- 7.1.3 Using a CUP/FUP Tape 84
- 81-81148-01 March 2004 7-3 85
- Drive Interface 86
- • Updating the same revision 87
- 7-6 March 2004 81-81148-01 88
- Insertion and Extraction 89
- Guidelines 89
- 8.1.1 General Status Packet 90
- 8.1.2 Loading a Tape 91
- 8.1.3 Unloading a Tape 92
- Configuration) 93
- 81-81148-01 March 2004 8-7 95
- Insertion Depth 97
- Cartridge Insertion Force 97
- Insertion Velocity 97
- Debounce Time 98
- Initialization Time 98
- 81-81148-01 March 2004 8-11 99
- Eject Distance 100
- Cartridge Extraction Force 100
- Extraction Velocity 100
- 81-81148-01 A02 102
Powiązane produkty i podręczniki dla Automatyczne ładowarki i biblioteki taśm Quantum SDLT 320
(294 strony)
(222 strony)
(34 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji