Quantum Scalar 100 Podręcznik Użytkownika Strona 44
- Strona / 52
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
40 Maintenance
Clearing Changes to the WWN for all FC ports
Use this procedure when you are removing an SNC 6101 that had its WWNs changed to match a pre-
existing unit.
1 Read the section Changing the WWN
on page 37.
2 Follow the instructions in Before Changing the WWN on a Replacement SNC 6101
on page 37.
3 Enter the wwnGlobalClear command.
The following messages are displayed:
This command will restore the WWN for Fibre Channel Ports.
This should only be done when there is no SNC set to this WWN.
You should never operate 2 FC devices that are set to the same WWN. This
may destabilize your SAN.
The unit will be rebooted after the WWN change.
Do you want to proceed (enter "yes" to continue):
4 Type “yes“ and press ENTER.
You are prompted for the password.
5 Type the password OverrideWWN and press ENTER.
This causes the SNC 6101 to reboot.
6 After the SNC 6101 has rebooted, enter the fcShowNames command to verify your changes.
The output in the Node Name column of the of the fcShowNames command should no longer match
the output previously saved before using the wwnGlobalClear command.
Clearing Changes to the WWN for one FC Port
Use this procedure when you are removing an SNC 6101 with the WWN on one port changed to match the
WWN of a pre-existing unit.
1 Read the section Changing the WWN
on page 37.
2 Follow the instructions in Before Changing the WWN on a Replacement SNC 6101
on page 37.
3 Enter the wwnPortClear <port> command.
The following message will appear:
This command will restore the WWN for Fibre Channel Port <x>. This should
only be done when there is no SNC set to this WWN.
You should never operate 2 FC devices that are set to the same WWN. This
may destabilize your SAN.
The unit will be rebooted after the WWN change.
Do you want to proceed (enter "yes" to continue):
CAUTION
The WWN override functions are available only through the service
port. These commands cannot be executed if attempted in a telnet
session.
CAUTION
The WWN override functions are available only through the service
port. These commands cannot be executed if attempted in a telnet
session.
- 89558 Böhmenkirch 2
- Contents 3
- 3 Installation 13 4
- 4 Scalar Firewall Manager 29 4
- 5 Maintenance 33 4
- Introduction 5
- Product Recycling 6
- Lithium Battery 6
- Laser Safety 6
- Usage Restrictions 6
- Getting More Information 7
- 4 Introduction 8
- Description 9
- Configuration Support 10
- Address Mapping 10
- Interface Protocol Awareness 10
- ADIC Management Console 10
- Access Security Capabilities 11
- Channel Zoning 11
- Scalar Firewall Manager 11
- Data Mover Module 12
- Interface Ports 12
- LED Indicators 13
- Specifications 14
- Operating Environment 15
- Supported Platforms 15
- Supported Devices 15
- Compliance 15
- 12 Description 16
- Installation 17
- Unpacking and Inspecting 18
- Pre-Installation 19
- 16 Installation 20
- Cabling the SNC 6101 21
- 18 Installation 22
- SNC 6101 User’s Guide 19 23
- 20 Installation 24
- Configuring the SNC 6101 25
- 22 Installation 26
- SNC 6101 User’s Guide 23 27
- 24 Installation 28
- Updating SNC 6101 Firmware 29
- 26 Installation 30
- SNC 6101 User’s Guide 27 31
- Verifying SNC 6101 Operation 32
- Host Registration Service 34
- Adding and Removing Hosts 35
- 32 Scalar Firewall Manager 36
- Maintenance 37
- Creating User Accounts 38
- Unlocking the Shell 38
- Using Telnet 39
- Removing the SFP 40
- Replacing the SFP 40
- Changing the WWN 41
- 38 Maintenance 42
- SNC 6101 User’s Guide 39 43
- 40 Maintenance 44
- Final Diagnostic Tests 45
- Updating the SNC 6101 46
- Post-Repair Checklist 47
- 44 Maintenance 48
- SNC 6101 User’s Guide 45 49
- 46 Index 50
- SNC 6101 User’s Guide 47 51
- 48 Index 52
Powiązane produkty i podręczniki dla Networking Quantum Scalar 100
Networking Quantum DPA Podręcznik Użytkownika
(101 strony)
(101 strony)
Networking Quantum PX506 Instrukcja Instalacji
(40 strony)
(40 strony)
Networking Quantum QVNR Instrukcja Użytkownika
(91 strony)
(91 strony)
Networking Quantum FC420 Podręcznik Użytkownika
(26 strony)
(26 strony)
Networking Quantum TC2201E Podręcznik Użytkownika
(202 strony)
(202 strony)
Networking Quantum TC2201 Podręcznik Użytkownika
(164 strony)
(164 strony)
Networking Quantum PX502 Podręcznik Użytkownika
(14 strony)
(14 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji