Quantum Scalar 1000 Podręcznik Użytkownika Strona 76
- Strona / 122
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
68 Configuring Channels and Devices
1 Expand the appliance in the navigation panel or the graphical panel.
2 Right-click the appropriate SCSI channel graphic.
3 Select Reset.
A warning is displayed.
4 Select Yes to continue.
The following message is displayed in the Status/Message Area:
Resetting SCSI Channel n on xxx.xxx.xxx.xxx. Please wait several minutes before doing a ‘Refresh’.
In this example, the “n” represents the SCSI channel number and xxx.xxx.xxx.xxx represents the IP
address of the appliance.
Configuring the SCSI Channel
The Configure command is used to change a SCSI channel’s mode, host ID, reset setting, and termination
status.
1 Log on as SAN administrator, portal administrator, or power user.
2 Expand the appliance in the navigation panel or the graphical panel.
3 Right-click the appropriate SCSI channel graphic.
4 Select Configure.
The SCSI Channel Parameters dialog box is displayed.
5 Use the drop-down boxes and check boxes to make changes to the configuration as necessary.
Refer to Channel Mode
, Host ID, Bus Reset on Power Up, Enable Termination,or Alternate Initiator ID,
below.
6 When you are finished viewing or setting SCSI channel parameters, select OK to continue.
The following message is displayed in the Status/Message Area:
Pending changes on xxx.xxx.xxx.xxx.
In this example, xxx.xxx.xxx.xxx represents the IP address of the appliance.
Select Cancel to cancel all changes and return to the main screen.
7 Reset the channel. Refer to R
esetting the SCSI Channel on page 67.
CAUTION
Use Reset carefully because it causes pending I/O commands to
return failed status back to the host operating system and may have
unexpected results. Make sure all I/O is stopped before issuing this
command. For instructions on doing so, refer to the appliance’s
Hardware User Guide.
Note
Basic users are not authorized to configure SCSI channels.
CAUTION
If you change any of the SCSI channel parameter settings, you must
reset the SCSI channel or reboot the appliance to use the new
settings.
- User’s Guide 1
- 89558 Böhmenkirch 2
- Contents 3
- 6 Managing User Accounts 39 5
- 7 Working with Portals 43 5
- 11 Configuring SAN Access 75 6
- 12 Troubleshooting the SAN 93 6
- A Glossary 107 7
- Description 11
- Using the SAN Client 12
- Event Logging 12
- 6 Description 14
- 8 Description 16
- Getting Started 17
- Before Installing AMC 18
- Installing the AMC Server 19
- 12 Getting Started 20
- Launching the AMC Server 21
- Installing the AMC Client 22
- Launching the AMC Client 23
- Connecting to the Server 24
- Logging on 25
- Logging off 26
- Exiting the AMC Client 27
- Shutting Down the AMC Server 27
- 20 Getting Started 28
- Frequently Asked Questions 29
- 22 Frequently Asked Questions 30
- How do I create policies? 31
- 24 Frequently Asked Questions 32
- The SAN Management Interface 33
- Received Event Trap Window 34
- Scalar i2000 38
- Device Numbering 40
- Graphical Panel 40
- Data Panel 41
- Max Speed 42
- Status/Message Area 43
- Common SAN Management Options 44
- Managing User Accounts 47
- 40 Managing User Accounts 48
- Adding a New User Account 49
- Modifying a User Account 50
- Deleting a User Account 50
- Working with Portals 51
- Modifying a Portal 52
- Deleting a Portal 53
- 46 Working with Portals 54
- Working with SAN Categories 55
- Creating a new Category 56
- Renaming a Category 56
- Deleting a Category 56
- Moving a Category 57
- Moving Items by Drag and Drop 57
- Working With Views 59
- Opening Saved Views 60
- Creating Views 60
- Saving Views 62
- Deleting Views 62
- Searching the Current View 62
- Reporting the Current View 63
- Configuring Email 65
- Configuring Policies 66
- Discovering the SAN 67
- Rediscovering a Segment 68
- Managing the SAN Appliance 69
- Refreshing Data 70
- Updating Firmware 72
- Using Restart 72
- Displaying RMU Data 73
- Managing the SCSI Channel 75
- Configuring the SCSI Channel 76
- Managing the Fibre Channel 77
- Resetting the Fibre Channel 78
- Configuring the Fibre Channel 78
- Managing a Device 80
- Editing Device Maps 81
- Pre-Assigning Device Numbers 82
- Configuring SAN Access 83
- Using Channel Zoning 84
- Data Mover Module 84
- Installing HRS 85
- 78 Configuring SAN Access 86
- 80 Configuring SAN Access 88
- Installing SFM 89
- 82 Configuring SAN Access 90
- Adding SFM Hosts 91
- Using eVPS 92
- Installing eVPS 93
- 86 Configuring SAN Access 94
- 88 Configuring SAN Access 96
- Deleting eVPS Hosts 97
- Using the eVPS View Menu 97
- Using VPM 98
- Making VPM assignments 99
- 92 Configuring SAN Access 100
- Troubleshooting the SAN 101
- Interpreting the Event Log 102
- 96 Troubleshooting the SAN 104
- Receiving Event Traps 105
- Monitoring the LED Panel 106
- Figure 21 SNC 4000 LED panel 107
- Figure 22 SNC 5100 LED panel 107
- Using Identify 108
- Monitoring Environmental Data 109
- Using Health Check 110
- Obtaining a Drive Dump 111
- Checking the Command Flow Log 112
- 106 Troubleshooting the SAN 114
- Glossary 115
- 108 Glossary 116
- 110 Glossary 118
- 112 Index 120
- 114 Index 122
Powiązane produkty i podręczniki dla Oprogramowanie Quantum Scalar 1000
(58 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji