Quantum Scalar 100 Podręcznik Użytkownika Strona 30
- Strona / 126
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4-20 6-00667-01 Rev B
Scalar 100
7. Remove the side covers. Looking at the rear of the library, unscrew the four Phillips screws that
secure each of the side covers (eight screws total). After removing the Phillips screws, open the
front door and slide the covers off the library.
8. Remove all drives and the DC power supplies from the library to reduce its weight. Each of
these items can be easily removed by loosening the captive thumbscrews and sliding the item
out of the chassis.
9. Standing at the front of the rack, use the handles on both sides of the Scalar 100 to lift and
position the library onto the rackmount hardware.
10. Slide the library into the rack until it stops.
Installing Side Panels
Your library can be setup as a floor model or a rackmount library. Read the following instructions to
configure your library as a floor model unit, by installing side panels.
Tools required:
• Large flat blade screwdriver or 3/8 nut driver
• Phillips screwdriver
To set up a floor model library
1. Verify that the Scalar 100 library is turned off using the main switch on the rear of the library.
Turning off power using only the front panel switch is not sufficient.
2. Fully open the front door of the library.
3. Install the side panel by capturing the vertical flange on the front of the library. The four holes
on the side panel should align with the four holes in the rear of the library.
4. Using a Phillips screwdriver, install the four thread-cutting screws contained in the Floor Model
Kit.
5. Repeat steps 1 through 4 to install the other side panel.
6. Close the front door of the library.
WARNING:
EVEN WITH THE ABOVE COMPONENTS REMOVED, THE SCALAR
100 WEIGHS IN EXCESS OF 150 LBS (65 KGS) AND REQUIRES
TWO PERSONS TO PROPERLY LIFT AND POSITION IT IN A RACK.
NOTE:
Both side panels are identical and can be installed on either side of the
library.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Powiązane produkty i podręczniki dla Automatyczne ładowarki i biblioteki taśm Quantum Scalar 100
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji