Quantum Scalar 100 Podręcznik Użytkownika Strona 69
- Strona / 126
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring your Library 8-59
Scalar 100
To configure additional library options
1. From the Main menu, select More. Select Setup and then select Utils. Select Config.
The Config dialog displays.
2. Using Yes/No, Next, and Change, set the following fields:
• Backlight on — Sets the backlight on or off. Possible values are Yes or No.
• Audio on — Determines whether key stroke sounds are made when a button is pressed.
Possible values are Yes and No.
• Scan on Init — Indicates whether the library will scan all tape cartridge barcodes when the
library is booted up. Note that either Scan on Init or Touch on Init must be enabled.
Possible values are Yes or No.
• Touch on Init — Indicates whether the library picker will touch all tape cartridges when the
library is booted up. Note that either Scan on Init or Touch on Init must be enabled.
Possible values are Yes or No.
• Mailbox — Determines whether the Mailbox will be used to import and export tape
cartridges or if the Mailbox will be used as storage slots.
• Imprt/Exprt — Indicates the Mailbox is for importing or exporting tape cartridges.
• Storage — Indicates the Mailbox is for storage.
3. Select OK.
Configuring Barcode Length
Use Media to configure the barcode length (volser) your library reads. By default, the library reads
an extended barcode label, 5 to 13 characters. However, you can configure your library to read six
character barcode labels.
For more information on barcode labels, see Barcode Label Requirements on page 10-76
.
Path: Main menu > More > Setup > Library > Media
To configure the barcode length
1. From the Main menu, select More. Select Setup and then select Library. Select Media.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Powiązane produkty i podręczniki dla Automatyczne ładowarki i biblioteki taśm Quantum Scalar 100
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.322 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji