Quantum Scalar 100 Podręcznik Użytkownika Strona 31
- Strona / 126
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Installing and Removing Hardware 4-21
Scalar 100
7. If you are installing casters on this library, refer to Installing Casters on page 4-21. Otherwise,
move the library to its permanent location.
If the Scalar 100 is installed on a raised floor with forced air below, ensure that a floor cutout is
beneath the library.
Installing Casters
Casters are an optional feature that are for use only with floor model library configurations.
Tools required:
• Large flat blade screwdriver or 3/8 nut driver
• Phillips screwdriver
To install casters
1. Place the Scalar 100 on its side for this procedure. Use the sling shipped with the library to tip
the library onto its side.
2. Using a Phillips screwdriver, remove the four rubber feet from the bottom of the library.
3. Install the two fixed casters to the back of the library with four bolts.
4. Install the two swivel casters on the front of the library with four bolts. Lock the two front casters
in place.
Installing/Removing a Drive
Follow the procedures below to install or remove a drive.
Installing a Drive
When installing drives into your library, note that drive types cannot be mixed. For example, SDLT-
320 drives cannot be installed with SDLT-220 drives and LTO-1 drives cannot be installed with LTO-
2 drives.
Tools required:
•None
To install a drive
1. From the rear of the library, find the lowest available drive slot. Loosen the two thumbscrews
on the filler plate and remove the filler plate. Store the filler plate in a safe location for future use.
Note that AIT tape drives cannot be installed in the bottom-most or top-most drive slot.
NOTE:
If you have difficulties installing or replacing a drive, try resetting the drive and/
or rebooting the library and host. Also, ensure that the new drive uses a unique
SCSI ID.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Powiązane produkty i podręczniki dla Automatyczne ładowarki i biblioteki taśm Quantum Scalar 100
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji