Quantum Scalar 24 Dokumentacja Strona 142
- Strona / 154
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
134 Troubleshooting and Diagnostics
90h Drive Error
Check Drive
Communication to a drive is
not working, the drive is not
initializing, or the drive is
reporting a problem.
Reboot the system. If the
problem persists, remove the
drive and re-install it. If the
problem still persists, contact
ATAC, you may need to
exchange the drive.
92h DRV Invalid
Call Service
Invalid drive firmware Reload drive firmware or call
ATAC.
94h Drive Media Error Indicates drive media error Remove the suspect tape
EAh Sled Missing
Check Sled
A drive sled has been
removed or is not connected
properly.
Re-insert the sled or check
the connections.
D0h PS Failure
Call Service
A library power supply failed
or is not operating within
specified ranges.
Reboot the system. If the
problem persists, contact
ATAC.
F0h Fan Failure
Call Service
A library or drive fan failed. Prevent the system from
becoming too hot and either
turn off the library or remove
the drive with the bad fan.
Contact ATAC.
80h and
E0h
Obstruction
Check Picker
The picker has reported a
move failure, which may be
caused by an obstruction of
the picker, such as: partially
extended tapes into the
picker path; an ejected tape
from a drive; or a tape within
the picker partially extending
out of the picker.
Try to clear the obstruction.
Contact ATAC.
E7h
E8h
Pick Failed
Clear Picker
Place Failed
Clear Picker
The picker could not get or
put a tape. Typically this
means a tape is still partially
in the picker.
Remove the tape from the
picker. For more information,
see Manual Removal of a
Tape From the Picker on
page 47.
E9h Tape Recovered
to Cell X
Informational message that
indicates that a tape had
been detected in the picker
assembly and was placed in a
slot location (X) to free the
picker and make it
operational.
Make sure that the tape
belongs in the location it was
placed. You may have to use
the Move Media function to
move the tape to the proper
location.
SAC
Code
Error Message Description Recommended Action
- ADIC Scalar 1
- Eschenstraße 3 2
- Contents 3
- 7 Operation 43 4
- 9 Using the Menus 61 5
- 11 Specifications 137 7
- Introduction 9
- 2 Introduction 10
- Intended Use 11
- Safety Precautions 12
- Regulatory Notices 12
- IC Notice (Canada Only) 13
- CE Notice 14
- VCCI Notices (Japan Only) 14
- Declaration of Conformity 15
- 8 Safety 16
- Description 17
- Features 18
- Optional Features 18
- Front Panel Components 19
- Interior Components 20
- Rear Panel Components 20
- Media and Media Protection 21
- Media Protection 22
- Host Interface 24
- Host Adapter 25
- Terminator 25
- Application Software 25
- SCSI Cables 25
- 18 Description 26
- Getting Started 27
- Installing Scalar 24 Hardware 28
- Connecting the Power Cord 30
- Inserting Tape Cartridges 31
- Setting up your Scalar 24 32
- Preparing the Host Computer 33
- Tape Driver Installation 34
- 28 Getting Started 36
- Installing Optional Hardware 37
- °F (38°C) 40
- Frequently Asked Questions 45
- More FAQs 46
- How do I clean a drive? 47
- What is partitioning? 48
- How do I get help? 49
- 42 Frequently Asked Questions 50
- Operation 51
- Menu Icons 52
- Drive Status Icons 53
- Tape Activity Icons 53
- Online and Offline Modes 54
- Inserting and Removing Media 54
- Manual Removal of Tapes 55
- Barcode Labels 56
- Menu Navigation 57
- Main Menu Navigation 58
- Submenu Navigation 58
- Normal Operations 59
- 52 Operation 60
- Using the RMU 62
- Configuring SNMP 63
- Configuring RMU User Accounts 64
- Configuring the Time and Date 65
- Updating Firmware 65
- Viewing Diagnostic Files 66
- Rebooting the RMU 66
- Viewing Logs 67
- Getting Help 67
- Using the Menus 69
- Main Menu 70
- Setup Menu 72
- Cancelling the Setup Wizard 73
- 66 Using the Menus 74
- 68 Using the Menus 76
- 70 Using the Menus 78
- 72 Using the Menus 80
- Configure Slots 81
- Configure Modes 82
- 76 Using the Menus 84
- Configure Partitions 85
- 78 Using the Menus 86
- Configure I/E Slot 87
- Set SCSI IDs 88
- Set Drive SCSI IDs 89
- Set Inquiry 90
- Access Mode 91
- User Interface 92
- Set Password 93
- 86 Using the Menus 94
- Configure RMU 95
- 88 Using the Menus 96
- Configure AutoClean 97
- AutoClean Partitioned Library 98
- Configure Barcode Scanner 99
- Reset Configuration 100
- Command Menu 101
- 94 Using the Menus 102
- Import LTO Cleaning Cartridge 103
- 96 Using the Menus 104
- Export Media 105
- Export Data Cartridge 106
- Export Cleaning Cartridge 107
- Dismount Drive 108
- Move Media 108
- 102 Using the Menus 110
- Bulk Load 111
- Bulk Unload 112
- Sequential 114
- Start Single 115
- Stop Sequential Backup 116
- Resume Sequential Backup 116
- Status Menu 117
- Display Firmware Version 118
- Display Inventory Information 119
- 112 Using the Menus 120
- Display Motion Counts 121
- Display Retry Counts 122
- Display Sensor Status 123
- Display Errors 124
- Display Serial Number 125
- Tools Menu 126
- Clean Drive 127
- Load Firmware 128
- Demo Test 128
- Self Test 130
- Drive Maintenance Test 131
- 124 Using the Menus 132
- Manufacturing Test 133
- Position Picker 134
- Output Logs 135
- Drive Power On/Off 136
- 130 Using the Menus 138
- Installation Problems 139
- Scalar 24 Error Messages 140
- Vital Product Data Recovery 143
- Environmental Considerations 143
- Specifications 145
- Storage Slot Count 146
- Library Storage Capacity 146
- Library Data Transfer Rates 146
- Operating Time 147
- Safety and EMC Standards 147
- Thermal Environment 148
- Acoustic 148
- Library Interface 148
- Reliability 149
- 142 Specifications 150
- 144 Index 152
- 146 Index 154
Powiązane produkty i podręczniki dla Automatyczne ładowarki i biblioteki taśm Quantum Scalar 24
(222 strony)
(34 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji