Quantum 1200 Series DAT Autochanger Podręcznik Użytkownika Strona 109
- Strona / 294
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
SDLT 600 SCSI Interface Guide Chapter 4: SCSI Commands
81-81200-02 REV A01 January 2005 4-67
4.9 MODE SELECT (6) / (10) Command (15h / 55h)
The MODE SELECT commands enable the host to configure the SDLT tape drive. Before configuring
the drive, the host should issue a MODE SENSE command to the drive to obtain a report of the current
configuration and determine which parameters are configurable. The host interprets this information
and then may issue MODE SELECT to set the drive to the host’s preferred configuration. The host
passes the Mode Parameter List (described in “Mode Parameter List” on page 4-69) to the drive during
the command’s DATA OUT phase.
Operating parameters for the drive are contained in several pages. The following table lists the MODE
SELECT pages supported and the location of the sections in this manual detailing each page:
Except for the EEPROM Vendor Specific Page (page 3Eh), the drive always powers on with its default
configurations set. This is also true if the drive receives a TARGET RESET message or a reset on the
RST line of the SCSI bus.
NOTE: See “Changeable Parameters Within MODE SELECT” on page 4-105 for
a list of changeable parameters within MODE SELECT. See “EEPROM
Vendor Specific Page (3Eh)” on page 4-134 for additional information
about how to use these changeable parameters.
Page Code Description Refer to
01h Read / Write Error Recovery Page Page 4-76
02h Disconnect / Reconnect Page Page 4-78
0Ah Control Mode Page Page 4-80
0Fh Data Compression Page Page 4-82
10h Device Configuration Page Page 4-84
11h Medium Partition Page Page 4-87
18h Logical Unit Control Page Page 4-89
19h Port Control Page Page 4-90
1Ch TapeAlert Page Page 4-92
25h Vendor Specific Configuration Page Page 4-95
3Ch Disaster Recovery Control Page Page 4-97
3Eh EEPROM Vendor Specific Page Page 4-98
SDLT 600
SCSI Interface Guide
SCSI Commands
81-81200-02
REV A01
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Powiązane produkty i podręczniki dla Oprogramowanie Quantum 1200 Series DAT Autochanger
(160 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji