Quantum 1200 Series DAT Autochanger Podręcznik Użytkownika Strona 172
- Strona / 294
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
MODE SENSE (6) / (10) Command (1Ah / 5Ah) SDLT 600 SCSI Interface Guide
4-130 January 2005 81-81200-02 REV A01
Table 4-73. TapeAlert MODE SENSE Page — Field Descriptions
Field Name Description
PS Parameters Savable. Always set to 0.
Page Code Identifies the type of MODE SENSE page being transferred. A value of 1Ch
identifies this as the TapeAlert Page.
Page Length Indicates the number bytes in the page, excluding bytes 0 and 1. The length is
returned in MODE SENSE commands and must subsequently be set to the
same value when performing MODE SELECT.
Perf Performance. Not supported. Always set to 0.
EBF Enable Background Function. Not supported. Always set to 0.
EWASC Enable Warning. Not supported. Always set to 0.
DExcpt Disable Information Exception Operations. Default value is 1. When set to 0,
the reporting method specified by the contents of the MRIE field is selected.
When set to 1, all information exception operations are disabled and the drive
ignores the contents of the MRIE field. When in this mode, the software polls
the TapeAlert Log page.
Test Always set to 0.
LogErr Error Log. Not supported.
MRIE Method for Reporting Informational Exceptions. The drive uses the contents of
this field to report information about exception conditions. Four methods are
available:
Value Method
00h No reporting of Informational Exception Conditions. The drive
does not report information exception conditions.
03h Conditionally Generate Recovered Error. This value is the default.
The drive reports informational exception conditions, if reports of
recovered errors are allowed, by returning CHECK CONDITION
status on the next SCSI command (except INQUIRY and
REQUEST SENSE commands) following detection of the
condition. The Sense Key is set to RECOVERED ERROR with
the Additional Sense Code set to 5Dh / 00h (TapeAlert event).
The SCSI command with CHECK CONDITION completes
without error before the report of any exception condition and
does not need to be repeated.
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Powiązane produkty i podręczniki dla Oprogramowanie Quantum 1200 Series DAT Autochanger
(160 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji