Quantum 1200 Series DAT Autochanger Podręcznik Użytkownika Strona 98
- Strona / 294
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
LOG SENSE Command (4Dh) SDLT 600 SCSI Interface Guide
4-56 January 2005 81-81200-02 REV A01
20 Clean Now Critical The drive needs to be cleaned. Make sure that all tape
operations have completed, eject the data cartridge
and follow the appropriate steps to use a cleaning
cartridge.
For detailed instructions about how to clean the tape
drive using a cleaning cartridge, refer to the User
Reference Guide for this product.
22 Expired
Cleaning Media
Critical The cleaning cartridge in use has expired. Wait for all
tape drive operations to complete, then use a valid
cleaning cartridge.
31 Hardware B Critical The drive may have a hardware fault. Contact a
service representative.
32 Interface Warning The drive has identified a problem with the interface to
or from the host.
34 Download Fail Warning The attempted firmware download failed.
36 Drive
Temperature
Warning The temperature inside the drive exceeds the allowable
specifications.
Note: The drive issues this warning 3 degrees C
below the maximum temperature threshold so
that you can provide additional cooling before
potential damage occurs.
38 Predictive
Failure
Critical A hardware failure of the drive is predicted. Call the
tape drive supplier help line to arrange for a
replacement.
51 Tape Directory
Invalid at Unload
Warning A WRITE error prevented the directory from being
updated when the drive unloaded the tape.
1. Severity levels are Informational, Warning, and Critical. Informational flags provide a status-type
message, Warning flags indicate that there is the possibility of loss of data, and Critical flags indicate
the possibility of loss of data and that user intervention, a service call, or both may be required.
Table 4-33. TapeAlert Flags, Severity Levels, and Meanings (Continued)
Flag
Severity
Level
1
Meaning
- 6'/7 1
- Table of Contents 3
- List of Tables 9
- List of Figures 15
- Introduction 21
- 1.3 Related Documents 22
- 1.4 Structure of this Manual 22
- 1.5 Conventions 23
- 1.6 For More Information 23
- 1.7 Reader Comments 24
- SCSI Parallel Protocol 25
- 2.3.1 Attention Condition 26
- RESET or DISCONNECT message 27
- 2.3.2 Reset Condition 28
- SCSI Messages 29
- 3.2 Supported SCSI Messages 31
- 3.2.1 ABORT TASK SET (06h) 32
- 3.2.2 TARGET RESET (0Ch) 33
- 3.2.3 TASK COMPLETE (00h) 33
- 3.2.4 DISCONNECT (04h) 33
- 3.2.5 IDENTIFY (80h - FFh) 34
- 3.2.10 MESSAGE REJECT (07h) 37
- 3.2.11 NO OPERATION (08h) 37
- WRITE BUFFER 3Bh Page 4-249 45
- 4.1.4 Behavior at Power-On 49
- 4.2 SCSI Command Descriptions 50
- 4.3 ERASE Command (19h) 52
- 4.4 INQUIRY Command (12h) 53
- Unit Serial Number Page (80h) 62
- • Logical Unit NAA Identifier 63
- Logical Unit NAA Identifier 66
- 4.5 LOAD UNLOAD Command (1Bh) 70
- 4.6 LOCATE Command (2Bh) 72
- 4.7 LOG SELECT Command (4Ch) 73
- 4.8 LOG SENSE Command (4Dh) 81
- Log Page” on page 4-43 90
- 0000h – 000Fh) 104
- — Field Descriptions 108
- SDLT 600 109
- SCSI Interface Guide 109
- SCSI Commands 109
- 81-81200-02 109
- 4.9.1 Mode Parameter List 111
- Mode Parameter Header 113
- SDLT tape drive 116
- Mode Page Descriptor 117
- 4.9.10 TapeAlert Page (1Ch) 134
- 4.10.3 MODE SENSE Mode Pages 155
- Control Mode Page (0Ah) 160
- Data Compression Page (0Fh) 162
- Medium Partition Page (11h) 167
- Port Control Page (19h) 169
- Parameter List 176
- Command (1Eh) 194
- 4.14 READ Command (08h) 195
- ATTRIBUTE LIST Service Action 202
- VOLUME LIST Service Action 203
- PARTITION LIST Service Action 204
- Attributes 205
- Attribute Identifier Values 207
- AND DEVICE 209
- Field Descriptions 212
- Standard Host Type Attributes 219
- Value Meaning 220
- 00h No code specified (ASCII) 220
- 01h - FFh Reserved 220
- 3C 03 A2 00 00 00 00 00 04 80 228
- 4.17.3 Data Mode (02h) 229
- 4.17.4 Descriptor Mode (03h) 229
- Command (A3h) 250
- Descriptions 251
- FUNCTIONS Command (A3h) 256
- 4.30 REWIND Command (01h) 274
- 2. Rewinds the tape 276
- 4. Rewinds the tape 276
- RESULTS command 277
- 4.33 SPACE Command (11h) 281
- 4.35 VERIFY Command (13h) 284
- 4.36 WRITE Command (0Ah) 285
- Exception Conditions 286
- 4.38.2 Write Data Mode (02h) 292
Powiązane produkty i podręczniki dla Oprogramowanie Quantum 1200 Series DAT Autochanger
(160 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji